2005 Land Rover Range Rover Oxygen Sensor - Downstream 8 Cyl 4.4L Bosch

The product worked fine. Tracking was a little iffy but I received it in five days. EMtSBy

i installed this and the 15717 on a 99 2.5L4 (5 speed) ford ranger. after the first tankful, it appeared that my mileage increased approx 5-8%, with the second tank showing a bit less. there was no 'check engine' light before or after. there are approx 175K miles on the vehicle, and i'm guessing the old ones were original.i used the parts selection page at bosch to confirm the part numbers: boschautoparts.com/auto/oxygen-sensors/premium-oxygen-sensors - hopefully, AutoPartsWAY won't blot out the link here.lately, i've noticed some missing at highway speed, but i think the computer has adjusted the fuel/air to a (more) optimal ratio, and plug/plug wire issues are more significant now. i plan to replace both shortly and will update after testing.one thing to note is that the threads in the exahust were pretty rusty and removal/installation was pretty difficult. i used an 18mm-1.5 tap to chase the threads, applied anti-seize and re-installed. be careful to...

This is an excellent replacement for the original part. It came well packaged with a small amount of special anti-sieze for the threads. I knew it was the right rear sensor on the Jeep (after my brother ran his diagnostic machine on the OBDI port) and looked all over the exhaust system until I finally found the located on the exhaust right near the back of the engine. I had expected it to be farther to the rear in the exhaust system. LoL.I was able to just jack up the right front of the car, disconnect the wire from the old sensor, unscrew the sensor with a regular 8" crescent wrench, apply the anti-sieze to the threads, screw the new sensor in, tightening it with the crescent wrench and connecting the wire connection. It fit like a charm. The special connector was exactly like the original and there were NO problems!This has been in my 2002 Jeep Grand Cherokee for over 3 months now and is working correctly. Perfect easy fix for a great price. I...

Sensor worked well car running good with no issues

I was completely satisfied with my purchase and will be purchasing more products from AutoPartsWAY, it's the best website for purchasing parts for your vehicles.This O2 sensor was an exact fit. Came out easy, went in easy. This sensor was half the price of Advanced Auto AND Auto Zone.

No problems after a couple years. Sold the car since.

Fit perfect in my 2000 Nissan Maxima SE (CA version).Was fairly difficult to get the old one out, but after a few days of PB Blaster soaking, it finally came out.Unfortunately, the reason I replaced the sensor was to take care of P0430, but it didn't work. (I knew it probably wouldn't but figured I spend $40 first before spending $200+ on a new precat).FYI - this is for bank 2 sensor 2replaces red wire sensor (this one has a black wire)

Bosch has worked well for me in the past with Mercedes Benz cars and with a Volkswagen. I'm unhappy to report that it did not work well with my Jeep Grand Cherokee 2004. I had to get an NGK for that car. The low voltage signal coming out of these sensors is actually too low for the PCM and every so often, I get a P0137 error.

Thanks

perfect fit...easy install

Perfecto... Works well and cheaper than autoparts

My mechanic just installed this for $54. It was perfect. I saved at least $100 because I had a $15 coupon on the labor. No more check engine light issues. Excellent product! I highly recommend that you buy this and just pay for the cheapest installation that you can find. Why get ripped off?

O2 sensors are a bugger to replace. That said, this item is as described. Delivered on time and with no issues. If you have to replace one, this is an economical replacement.

Installation quick & easy. No Codes. I assume it working like it should.

=)

okay it works

Fixed the code. Dealer wanted some $275+. Fixed it with less than $100 sensor..

I originally bought the Bosch 15703 for my 2000 Chevy K3500 pickup since the site said that one would fit. If I'd have scrolled down further I'd have found this one that said it fit as well. the 15703 did not fit so I had to return it and order this one. This one fit and seems to have fixed my promble. Compared the price at my local autoparts stores and this part is identical to what they sell but for far less. Thanks AutoPartsWAY!

Perfect fit,,fast delivery

I used this to replace the one wire O2 sensor that I installed during a carb to EFI/TBI conversion. The one wire would fall out of closed loop and take too long to go into closed loop. This goes into closed loop quickly and according to the scan software, is working perfect.I tapped in to the fuel pump wire to drive another relay that powers the heater wires (two white wires - one ground and the other hot). This prevents the O2 sensor from going hot with the ignition in the on position, but engine off.

I was in the import car parts biz for over 30 years and this Bosch Oxy Sensors is the original factory for my Nissan Frontier as my truck still had the original sensor in it since new. The one I took out was made by Bosch not NGK/NTK or Denso and replacement was easy

The Bosch #13942 Oxygen Sensor fit my wife's 1990 Taurus with 3.0L Vulcan V6. With the new sensor, the car has a smoother idle than with the 24 years 115,000+ miles old original oxygen sensor. The anti-seize coating pre-applied to the threads was a nice touch, one less step for me to perform during installation. The price was low enough that I felt it was worthwhile to do as part of a high-mileage tune-up at home, and I'm satisfied with the new Bosch sensor.

outstanding product, at half the price of the local auto parts shops! fit perfect, and had more than enough wire-lead!

Fit perfect in my car

Fits perfectly in our 2002 Chevy Cavalier. This O2 sensor has a factory plug on it for a direct fit.

Perfect fit for a 2000 Chevy Cavalier. The old one was very difficult to remove because it was seized in there. The new one fit just fine and the connector snapped right in without a hitch.

100% happy

This product was great just like I expected. Very quick delivery and the price was excellent I recommend this item to anyone.

Fit fine on 2002 Jeep Grand Cherokee. This unit replaced the passenger side rear sensor and cleared my error code. No modification to the wiring was needed.

Fit my truck like it was supposed to. Hardest part of installation was getting the old one off. After 2 days the check engine light went off, I didn't even need to go in and clear the code. It's been a month and the light is still off so the sensor must still be working! Saved over $20 by buying it on AutoPartsWAY instead of my local part store. The part store was offering the same part with the same brand so that means this isn't a cheap knock off part like I suspected it might be. Arrived 2 days before estimated shipping date. Very pleased

Replacing my sensor took care of the check engine light and improved the gas mileage on my '95 Wrangler 4 cyl, 5 speed from 10 to 15! Exhaust now smells much better too!I used "Powerbuilt 648691 Oxygen Sensor Offset Puller" tool to remove and reinstall, I started soaking the old sensor with WD40 a few days ahead of time, came out without too much argument.Good luck, SFC

If you're a DIYer like me, this can save a ton of $$$ doing this repair by yourself! It's simple to do if you have the right equipment to do it. Get a O2 Cesnsor socket for under $20 on line or at your local automotive store and the original comes right off and the new ones go right on with the perfect fit as the originals. Already had sealant on the threads so that was a nice surprise!

Unbelievably enough, it fits and (as far as I know even though I didn't do the extended sniff test from the tailpipe to make sure) I believe it works as it should. There's not much else to say...

This is the second Bosch O2 sensor I've used. Both fit perfectly and the emissions at the tail pipe on both cars improved after their installation. They build a fine sensor, possibly the best.

This is a DOWNSTREAM EXACT FIT O2 Sensor for a 2007 KIA SPECTRA EX 2.0L.I don't regret buying it. This is Part # 13461 BOSCH Brand from advance auto parts. The price was not the cheapest available online and in-store, but I found the cheapest upstream sensor on AutoPartsWAY. So I purchased both at the same time.If you are looking for the UPSTREAM sensor get the BRAND: NTK Part # 24353 this is the same as advance auto parts. I went crazy looking for the upstream one. Because I needed the 5-wire not 3 or 4 that they usually come in.I just changed these sensors this passed weekend.

Original for my 1999 Nissan Frontier, 2.4L, KA24DE engine. Delete the old and place the new and ready, nothing else to do ...

this is a brand new bosch o2 sensor, it fits properly and works properly. also the price is unbeatable! you could literately buy two of these for the price of the same exact one from an auto parts store!

Fast delivery, sensor fit and worked perfectly. Thanks Why on Earth do they now require twelve more words before they accept my post?

Worked perfectly in my Saturn. No more Service code! This thing popped in about 2-minutes, once I broke loose the old one, which was a bear!

A truckA rough-running truckA mysterious misfirePlug in the scanner, check the live feedA lethargic O2 sensor on the right bank.Like tortoise and hare, night and dayChecked auto parts stores, oh what a mess!Some out of stock, some wanting more than I care to sayTook down the part number, and came here for half price.Out with the old, in with the new.Problem still not gone, but a tad better now.And the sensors? Their voltage changing rapidlyLike two happy hares!

Easy and convient way to order parts. The price was good on both parts that I could tell even with the cost of shipping and handling!

This was a great choice: perfect fit and perfect results..As soon as I replaced the O2 sensor on my 2003 New Beetle GLS, the codes cleared and the check engine light went off.I'm looking forward to seeing an improvement in my gas mileage.*** Update *** February 28, 2014Used a full tank of gas. My usual 20 miles per gallon jumped to 23.7 MPG. I was more than delighted.Doing the math, my cost per mile for gas dropped from 18.8 cents per mile to 15.8. That's a 16% reduction in gasoline cost.Added benefit: my Beetle drives like it has been supercharged.

This is the sensor I received for my 94 ( non CA emissions ) Ranger from a local parts store, It will not work, the tabs on the outside of the connector are not in the same position as OEM Motocraft part# DY649, It can be made to fit by filing off the tabs on the connector but will not send proper signal to the ECU. i'm sure it's not a bad sensor for other applications, but people need to quit selling this for a 94 ranger, it will not work.

The check engine light on my 2005 F150 FX4 came on awhile back. I scanned the PCM and got a P0059 code, HO2S Heater Resistance (Bank 2, Sensor 1). I performed the diagnotics suggested and narrowed it down to the O2 sensor. At AutoPartsWAY I saved $20 over the local auto parts stores, and had the part in no time. Note the Bosch O2 sensor has anti seize preapplied to the threads, so it's ready to go.

Nothing required for 2004 Gold 2.0. Direct fit no problemsCodes cleared all works. Thank you very much for this great part.

This was installed on a 2002 1500 Chevy Silverado and it went in like a charm. The sensor is recording as it should (I have a computer to read it as the car is running) and my MPG has increased since installing the new sensor. No problems would recommend

Installation was a snap. It fit a 2004 Chevy Cavalier perfectly. No soldering of wires required for installation. Definitely recommend.

I replaced the old upstream ACDELCO oxygen sensor from the exhaust manifold of my Chevy Colorado 3.5L with this one, and it works as advertised. It comes with a small pouch of copper anti-seize for the threads.

worked perfectly it was good replacement on my 07 jeep wrangler. alot cheeper than autozone and the exact same part.

I put this in my 97 wrangler it works great. The only problem was that the connection did not fit so I had to cut the wires and connect them to the old connector. Not sure why mine didn't fit since others didn't seem to have that problem. My Jeep definitely runs better now.